Christian Manliguez Lim
Auto tinter/Auto detailer/Auto Polisher/ Car Wrapping / Paint Protection Film Installer (PPF)/Carbon Fiber Installer

Summary of Qualifications

• Able to learn new skills effectively
• Effective communication and interpersonal skills
• Strong organizational skills and time management skills
• Energetic and enthusiastic
• Punctual, reliable and trustworthy

Work Experience

Date : June, 2013 – July, 2015
Position : Auto Tinter, Paint Protection Film Installer, Auto Polisher and Detailer
Company Name : Al Wuhaibi
Location : Riyadh, Kingdom of Saudi Arabia
Department :Car Accessories
Reason for leaving : Finished Contract

Job Description :

Step by Step procedure in Tinting installation:

Side Windows
• Clean the car thoroughly to ensure that it is dustless
• Spray water with shampoo into the glass
• Put tint in the outside glass as pattern
• Cut the sides according to the shape of the windshield
• Clean the inner surface of the glass thoroughly using a metal pallet or scraper blade
• Hold the tint carefully and peel away the plastic liner
• Continuesly spray solution when you put the tint into the glass
• Press the excess water under the film using squeegee then use plastic card
Windshield, Back Windows
• Spreading powder upon the glass surface
• Spray water only on both left and right vertical sides
• Put the tint then cut the edges
• Point heatgun start to every corner going to the midst of upper or lower sides
• Continue till all lines shrink
• Clean inner surface thoroughly
• Keep tint wet while peel away the plastic liner
• Spray solution into the glass to move easily
• Apply tint carefully, push water out by using wiper then squeegee for final touch

Step by Step Procedure in PPF Installation
• Wash the vehicle and make it sure that the vehicle is dry and cold before installation
• Wash your hand properly before installation to prevent fingerprints.
• Clean the surface with alcohol solution to wash away grease before installation.
• Using the Soap Solution, spray your fingers, the application area on the vehicle and the adhesive side of the film. The Soap Solution allows you to slide the film into its desired position.
• Properly position the film. If stretching is not required, squeegee out the Soap Solution. Dry the surface with a soft, clean cloth, such as a 3M Perfect-It™ III Detailing Cloth and look for bubbles.
• To remove remaining solution beneath the film, squeegee from the center point of the application and slide toward the edges of the film.
• If film fingers have formed (linear film pockets, formed at the edge of the film that have not adhered to the painted surface after initial squeegeeing), spray inside the fingers with Alcohol Solution and re-squeegee. This motion pushes out any remaining solutions.
• Wipe the film with a 3M Perfect-It III Detailing Cloth to get a clear look at the application. Other types of cloths may scratch the surface of the film. There may still be some water pockets or air bubbles remaining. Re-wet the surface and your fingers with the Soap Solution and re-squeegee.
• If you cannot get the air pockets or bubbles out, the film can be lifted and re-applied within five minutes of application completion. Be sure to re-wet the film, the vehicle and your fingers before you lift the portion of the film that has bubbles. Use the same squeegee technique, starting at the center point of the application and sliding the squeegee to the edges of the film.
• Repeat this procedure on the second half of the film.

• Job Description : Auto Detailler and Polisher
• Cleans and refurbishes new and used automobiles, performing any combination of following duties: Washes vehicle exterior to clean cars, using cleaning solution, water, cloths, and brushes.
• Applies wax to auto body, and wipes or buffs surfaces to protect surfaces and preserve shine, using cloth or buffing machine.
• Vacuums interiors of vehicles to remove loose dirt and debris, using vacuum cleaner.
• Cleans upholstery, rugs, and other surfaces, using cleaning agents, applicators, and cleaning devices.
• Applies revitalizers and preservatives to vinyl or leather surfaces, and treats fabrics with spot and stain resistant chemicals to preserve and protect interior components.
• Cleans engine and engine compartment with steam cleaning equipment and various cleaning agents to remove grease and grime.
• Applies special purpose cleaners to remove foreign materials which do not respond to normal cleaning procedures, utilizing experience and following recommendations of product manufacturer.
• Paints engine components and related parts, using spray gun or aerosol can and masking material.
• Applies paint to chipped body surfaces of vehicle, using container of touchup paint.
• Applies dyes and reconditioning chemical to vinyl tops of vehicle to restore color and condition.

Tools and Machines/Equipment used:
Cutter Blade, Bluemax Squeegee, Wiper, Metal pallet, Card, Spray Solution, Spray Gun, Clean Cotton Cloth, Scraper and Heat Gun, Plastic Slammer, Buffing Machine, Air Compressor, Vacuum Cleaner, Pressurize Car Wash

Types of Stickers used:
• ASWF ( American Standard Window Film)
• 3M (Window Film)
• 3M (Venture Shield and Scotch Guard ) PPF

Other Duties (Designing, Planning etc.):

• Ability to estimate time of service or repair job for purposes of efficient scheduling

2)

Date : November, 2010 to January, 2013
Position : Auto Polisher and Detailer, Quality Control (paint section)
Company Name : AL MOHTASEB SERVICES
Location : Doha, Qatar
Department : Quality Control
Reason for leaving : Finished Contract

• Job Description : Auto Detailler and Polisher
• Cleans and refurbishes new and used automobiles, performing any combination of following duties: Washes vehicle exterior to clean cars, using cleaning solution, water, cloths, and brushes.
• Applies wax to auto body, and wipes or buffs surfaces to protect surfaces and preserve shine, using cloth or buffing machine.
• Vacuums interiors of vehicles to remove loose dirt and debris, using vacuum cleaner.
• Cleans upholstery, rugs, and other surfaces, using cleaning agents, applicators, and cleaning devices.
• Applies revitalizers and preservatives to vinyl or leather surfaces, and treats fabrics with spot and stain resistant chemicals to preserve and protect interior components.
• Cleans engine and engine compartment with steam cleaning equipment and various cleaning agents to remove grease and grime.
• Applies special purpose cleaners to remove foreign materials which do not respond to normal cleaning procedures, utilizing experience and following recommendations of product manufacturer.
• Paints engine components and related parts, using spray gun or aerosol can and masking material.
• Applies paint to chipped body surfaces of vehicle, using container of touchup paint.
• Applies dyes and reconditioning chemical to vinyl tops of vehicle to restore color and condition.
Tools and Machines/Equipment used:
Buffing Machine, Sand Paper, Vacuum Cleaner, Spray Gun, Pressurized Car Wash

3)
Date : March 2008 to July 2010
Position : Auto Tinter, Auto Paint Protection Film Installer, Auto Polisher and
Detailer, Car Wrapping
Company Name : SINAN BU KHAMSIN
Location : Kingdom of Saudi Arabia
Department : Car accessories
Reason for leaving : Finished Contract

Step by Step procedure in Tinting/Sticker installation:

Side Windows
• Clean the car thoroughly to ensure that it is dustless
• Spray water with shampoo into the glass
• Put tint in the outside glass as pattern
• Cut the sides according to the shape of the windshield
• Clean the inner surface of the glass thoroughly using a metal pallet or scraper blade
• Hold the tint carefully and peel away the plastic liner
• Continuesly spray solution when you put the tint into the glass
• Press the excess water under the film using squeegee then use plastic card
Windshield, Back Windows
• Spreading powder upon the glass surface
• Spray water only on both left and right vertical sides
• Put the tint then cut the edges
• Point heatgun start to every corner going to the midst of upper or lower sides
• Continue till all lines shrink
• Clean inner surface thoroughly
• Keep tint wet while peel away the plastic liner
• Spray solution into the glass to move easily
• Apply tint carefully, push water out by using wiper then squeegee for final touch

Step by Step Procedure in PPF Installation
• Wash the vehicle and make it sure that the vehicle is dry and cold before installation
• Wash your hand properly before installation to prevent fingerprints.
• Clean the surface with alcohol solution to wash away grease before installation.
• Using the Soap Solution, spray your fingers, the application area on the vehicle and the adhesive side of the film. The Soap Solution allows you to slide the film into its desired position.
• Properly position the film. If stretching is not required, squeegee out the Soap Solution. Dry the surface with a soft, clean cloth, such as a 3M Perfect-It™ III Detailing Cloth and look for bubbles.
• To remove remaining solution beneath the film, squeegee from the center point of the application and slide toward the edges of the film.
• If film fingers have formed (linear film pockets, formed at the edge of the film that have not adhered to the painted surface after initial squeegeeing), spray inside the fingers with Alcohol Solution and re-squeegee. This motion pushes out any remaining solutions.
• Wipe the film with a 3M Perfect-It III Detailing Cloth to get a clear look at the application. Other types of cloths may scratch the surface of the film. There may still be some water pockets or air bubbles remaining. Re-wet the surface and your fingers with the Soap Solution and re-squeegee.
• If you cannot get the air pockets or bubbles out, the film can be lifted and re-applied within five minutes of application completion. Be sure to re-wet the film, the vehicle and your fingers before you lift the portion of the film that has bubbles. Use the same squeegee technique, starting at the center point of the application and sliding the squeegee to the edges of the film.
• Repeat this procedure on the second half of the film.

• Job Description : Auto Detailler and Polisher
• Cleans and refurbishes new and used automobiles, performing any combination of following duties: Washes vehicle exterior to clean cars, using cleaning solution, water, cloths, and brushes.
• Applies wax to auto body, and wipes or buffs surfaces to protect surfaces and preserve shine, using cloth or buffing machine.
• Vacuums interiors of vehicles to remove loose dirt and debris, using vacuum cleaner.
• Cleans upholstery, rugs, and other surfaces, using cleaning agents, applicators, and cleaning devices.
• Applies revitalizers and preservatives to vinyl or leather surfaces, and treats fabrics with spot and stain resistant chemicals to preserve and protect interior components.
• Cleans engine and engine compartment with steam cleaning equipment and various cleaning agents to remove grease and grime.
• Applies special purpose cleaners to remove foreign materials which do not respond to normal cleaning procedures, utilizing experience and following recommendations of product manufacturer.
• Paints engine components and related parts, using spray gun or aerosol can and masking material.
• Applies paint to chipped body surfaces of vehicle, using container of touchup paint.
• Applies dyes and reconditioning chemical to vinyl tops of vehicle to restore color and condition.

Step by Step Procedure in Car Wrapping

• Make sure you have images of the vehicle prior to planning the design.
• Determine where all the joins will fall. Use the natural lines of the vehicle, whether horizontal or vertical. Use door panels/weld lines to cover overlaps.
• Thoroughly wash the vehicle down with soap and water and allow 24 hours to dry, paying extra attention to door seals and wheel arches.
• Degrease the vehicle. Mactac recommend isopropyl alcohol. Alternatively use a fast drying panel wipe with silicone killer paying special attention to all the recesses.
• For solvent printed media allow a minimum of 48hrs to outgas. The rolls should be left standing vertically and loosely wound to help with airflow and should be turned regularly as the solvents are heavier than air. The more the vinyl can be allowed to de-gas, the less tacky the adhesive will feel and the easier the graphic will be to fit.
• Laminate with cold rollers only. Do not use excessive tension on the rollers.
• Use a hard Mactac squeegee or similar. Apply a strip of velvet to one edge and change the velvet regularly to avoid scratching.
• Apply the vinyl to the flattest part of the panel first (create a base line) working from side to side, keeping the vinyl as level as possible. Stretch the vinyl without heat over the whole area and do not work the film into the more complicated areas such as recesses until later.
• When stretching the vinyl, always pull outwards from the largest area of the vinyl you can to spread the tension. This also applies when you use extra heat to soften and stretch the vinyl, apply heat to a larger area than you need as this should help to avoid distorting the graphic.
• When cutting through the vinyl on the bodywork or around handles it is best to stick electrical tape to the surface first. Use a new blade each and every time you cut through the vinyl. The weight of the blade should be enough without having to apply extra pressure.
• Post heat to 95ºC or above and always use an infra red temperature gauge to be sure that you have reached this temperature. Anything less and the vinyl will retain its memory and cause the graphic to pop out of recesses and curves. This post heating must be carried out scrupulously on all areas where the wrap has been stretched to fit, especially in deep recesses. Do not overheat as you may damage the film.
• If vehicle wrapping in colder weather do not let the vehicle leave the workshop until the following day. The vehicle and vinyl should be allowed to cool down at the same rate as the workshop. This will help to avoid thermal shock and reduce the risk of failure in the recesses.

Tools and Machines/Equipment used:
Cutter Blade, Bluemax Squeegee, Wiper, Metal pallet, Card, Spray Solution, Spray Gun, Clean Cotton Cloth, Scraper and Heat Gun, Plastic Slammer, Buffing Machine, Air Compressor, Vacuum Cleaner, Pressurize Car Wash

Types of Stickers used:
• Solar Guard
• 3M (Venture Shield and Scotch Guard ) PPF

Educational Background

Inclusive Date: June 1997, March 1999
Course: BS in Education
College School: University of Southern Mindanao
Location: Kabacan, Cotabato

Inclusive Date: June 1996 to March 1997
Course: BS Accountancy
College School: Notre Dame University
Location: Cotabato City

Inclusive Date: June, 1992 to March 1996
High School: Notre Dame of Makilala
Location: Makilala, Cotabato

Personal Data

Date of Birth : October 02, 1979
Place of Birth : Cotabato City
Height : 5”4
Weight :65kg
Religion :Catholic
Languages Spoken : English, Tagalog, Bisayan
Cell Number :+639074102013
Landline Number :n/a
Email :[email protected]
Skype ID :butch.belgica64
Facebook Name/Email : Christian Manliguez Lim
Citizenship : Filipino

Civil Status : Married
Spouse’s Name : Janice Reambonanza Lim
Children’s Name/Age : Ramon Jaime R. Lim/ 5years old

Current Address : Saguing, Makilala, Cotabato
Home Address : Saguing, Makilala, Cotabato

Emergency Contact Name :Janice R. Lim
Relationship :Wife
Emergency Contact No. :0922-761-3446

Character References

• Available upon request.