Education

2003/2010 Higher National Diploma at Petroleum Training Institute

Mechanical Engineering

Experience

2018/Present Senior Mechanical Technician at prime Atlantic Celegec

: planning and implementing preventive maintenance schedule for machinery
to increase machine up-time / equipment reliability.
▪ Proficient in working with vendors to enhance process equipment , thereby
achieving the required quality jobs.
▪ Provide technical assistance to field service personnel during project,
installation and maintenance repair GE gas turbine PGT 25+G4, auxiliary and
Turbine engine support equipment on Total Egina FPSO
▪ Routine checks for turbine component and auxiliaries for any leakages,
malfunctioning, defect, damage and ensure timely repairs of deficiencies.
▪ Perform preventive maintenance and emergency repairs on gas turbine
auxiliaries and support equipment in accordance with OEM maintenance
manuals.
▪ Monitored and record gas turbine operating parameter such temperature,
pressure, vibration, speed, level for equipment history through Human machine
Interface (HMI).
▪ Proficient in reading blueprint diagrams and/or technical manuals to facilitate
troubleshooting and repair on Gas Turbine, Diesel Engine (Caterpillar Diesel),
Gas compressors, Pumps etc.
▪ Performed preventive maintenance, Troubleshooting and overhauling of
different kind of (API & ISO Standard equipment) such as centrifugal
pumps(Sulzer, Flowserve, Spx), Centrifugal compressors (GE), Centrifuge
separators, reciprocating pumps, Reciprocating compressors, gear box and
blower.
▪ Carried out motor solo run and monitoring of parameter (vibration,
temperature and rpm).
▪ Rectified shaft alignment on rotating equipment such as pumps and electric
Motors.
▪ Reviewed mechanical maintenance work from junior technician to ensure the
right material, procedures, tools and equipment are use.
▪ Carried out daily inspection and preservation on chemical injection package, air
compressor packages, fuel gas compressor packages, Gas turbine
package, subsea methanol injection package, crude oil transfer pump, essential
diesel generator.
▪ Used SAP to raised notification, prepare work order, time writing, report
completed jobs and close jobs.

2011/2018 Mechanical Technician at Pivot Gis Nigeria Ltd

▪ Planned and execute maintenance task in conjunction with my team and make
The required arrangement to carry out assigned tasks in an efficient and safe
manner.
▪ Used computer maintenance management system (CMMS) to register,
Prepare, view and document equipment history and give daily report on job
Status and completed jobs.
▪ Predictive maintenance scope on vibration analysis for pumps, compressor
and electric motor to ascertain health condition of the equipment.
▪ Diagnostic checks using Thermography equipment on reciprocating and
Centrifugal compressor, pumps and electric motors etc.
▪ Collect oil sample on pumps, reciprocating and centrifugal compressors to
analysed the health condition of the equipment.
▪ Overhaul, repair, installation and service reciprocating compressors,
Centrifugal compressor(Siemens), gas turbine, gas engine and gear accessory in
accordance with standard service procedures.
▪ Monitor, inspect and verify completed work on rotating equipment such as
Centrifugal pumps, reciprocating compressors, centrifugal compressor, lube
oil system and accumulators.
▪ Interpret design specifications, codes and standards, drawings and technical
manuals in dis assembly and assembly of reciprocating compressors, and gas
engine.
▪ Mechanical seal flow measurement on rotating equipment such reciprocating
and centrifugal compressor.
▪ Removed and re-instate mechanical seal, thrust and radial bearing, journal
bearing, sleeve, impeller, wear rings on centrifugal Pumps, centrifugal
compressors.
▪ Used laser alignment equipment in aligning two-shaft equipment such as
pumps and electric motor and run out check on shaft .
▪ Troubleshooting, fault-finding and overhaul of hydraulic power unit
(HPU), hydraulic actuators for ESD Valves , and hydraulic cylinder.
▪ Efficient interpretation of single line drawings, Block, PFD/PFS, P&ID/PEFS
and location diagrams.