Jaimin Amin

C202 2404 119 ST NW

Edmonton, Alberta, T6J 4H1

Cell: 780-607-4996

[email protected]

Profile:
·         Bachelor of Mechanical Engineering degree and Mechanical Engineering Technician Diploma holder with Engineering and Quality Control experience.

·         International educational credentials approval by International Qualifications Assessment Service (IQAS) as Mechanical Engineer in Canada.

·         CWB Level II (CSA W178.2 and ASME B31.3 )

·         NACE  CIP LEVEL 2 ( COATING INSPECTOR)

·         One month training in Gas Turbine Power Plant (72 MW).

·         Experience with RBMI-Risk Base Mechanical Integrity and Ultra Pipe Software.

·         Experience with HRSG and OTSG new construction and in-service inspection quality control.

Good knowledge in ASME B31.3,B31.1, ASME Section VIII Division I,ASME Section II Part A/B/C, API 572 , API 570, API 686.
Skilled in Microsoft Office, AutoCAD 2013, AutoCAD 3D, Ultra-Pipe and RBMI, SAP, Microsoft Project.
Strong oral and written communication with multi-discipline on job sites.
Work well in a High Pressure Environment.
Attentiveness in the implementation of all Lean Manufacturing Process
Demonstrated accuracy, attention to detail and ability to work well in a team environment.
EMPLOYMENT:
INPRO INSPECTION INC.                                                                                                  Apr 2017 – Present

Fort McMurray, Edmonton

New Construction:

Mechanical Field Engineer for the new construction project of Installation of Process Piping at Suncor – Fort Hills facility.

Duties:

·         Involved in Tube replacement of addition project for OTSG.

·         Created, Implemented and followed ITPs

·         Weld Inspection

·         Performed visual inspection of ASME Section I, BEP and NBEP welds

·         Verify welder qualifications and Performed welder site orientations.

·         Plan, schedule and dispatch Non-Destructive Testing Personnel in accordance with project requirements

·         Inspection of Control Valve, Gate Valve and Butterfly Valve according to Spec prior to Installation

·         Updated history dockets on daily basis

·         Reviewed MTRs for code compliance

·         Create Hydro-Test Procedure and Conduct Hydro test of HRSG and OTSG.

·         Creating procedure for Pneumatic test for OTSG and HRSG

·         Conduct Pneumatic test of HRSG and OTSG.

·         Review Turnover Package.

·         Coordinate with Client and/or Authorized Inspector on all requested inspection activities

·         Coordinate Quality team member activities in conjunction with construction activities and
Prepare required documentation and maintain files for final turnover to the client

·         Co-ordinated all ABSA site inspections.

Mechanical Engineering Technologist (Reliability Planner)                                           June 2016 – March 2017

West Fraser Ltd – Pulp Mill

Hinton, Alberta

·         coordinating maintenance contractors to execute work scopes, and

·         coordinating mill crews and maintenance contractors to carry out emergency repairs when encountered.

·         Administer all required weekly/monthly/annual testing of the fire system

·         creating inspection plans for monitoring equipment damage,

·         creating damaged equipment maintenance scopes

·         Proficient using a CMMS – Maximo as well as scheduling systems

·         Maintains a library of event job plans, using Maximo as the system of record

·         Build asset registry in Computerized Maintenance Management Systems  program and perform all updates as assets are moved, added, or divested

·         Build and implement a natural gas system maintenance program.

·         Review, creation, and revision of Standard Operating Procedures (SOPs)

·         Ensure PM (Preventative Maintenance) programs are created, followed, and executed on schedule

·         Track and implement work order system through

·         Maintain the integrity of fire systems including underground firewater piping,

·         Firewater pumps, fire hydrants, PIV’s, sprinkler systems.

Mechanical Engineer

INPRO INSPECTION INC.                                                                                                June 2013 – June 2016

Fort McMurray, Edmonton

New Construction:                                                                                                                                         Mechanical Field Engineer for the new construction project of Installation of Process Piping at Pembina NGL Corporation, Red-water facility.

·         Perform field surveillance inspections monitoring the contractor workmanship and efficiency.

·         Create RFI (Request for Information), NCR (Non Conformance Report) and CSR (Construction Surveillance Report).

·         Hydro Test Witness for Process piping

·         Welding inspection for piping installation.

·         Torque verification for re-instatement for piping.

·         System turnover Review and final walk down with client.

New Construction:                                                                                                                June 2014 – Aug 2015

Mechanical Field Engineer and NACE Inspector (Static and Rotating Equipment and Pipeline Integrity Specialist, HVAC) for the new construction project of Installation Static, Rotating Equipment and HVAC Unit at CNRL, Fort Mcmurray – Horizon facility.

Duties:

·         Perform field surveillance inspections monitoring the contractor workmanship and efficiency.

·         Discuss Engineering Problem Regarding installation of Equipment.

·         Create ITP for Static Equipment (Cyclone and Air Receiver) and Rotating Equipment (Pump and Compressor) Installation, Pressure Vessel, Weir Gate and Under Ground piping and process piping installation.

·         Check Installation of pump according to API 686.

·         Analyzes and documents the cause of rotating equipment failures.

·         Performs Failure and Root Cause Failure Analysis.

·         Develops and implements proactive, predictive and preventative maintenance processes.

·         Check and Review Laser alignment Report and Pipe strain Report

·         Performing Equipment criticality reviews and Assessments.

·         Coordinates and provides technical support and recommendations for rotating equipment repairs, in-house and outside

·         Check Installation of HVAC Units.

·         Witnessing Anode Installation in warm water tank and Under Ground piping

·         Welding Inspection of piping and structural.

·         Inspecting surface for coating.

·         Witnessing pre-Coating tests according to NACE standards.

·         Inspection of Wall Cladding as well as Piping Insulation.  .

·         Create RFI (Request for Information), NCR (Non Conformance Report) and CSR (Construction Surveillance Report).

·         Collaboration with the Construction Project Team in planning and scheduling for walk downs and the transfer of care custody and control (TCCC) of turnover commissioning packages from Construction to plant.

·         Reading Engineering Drawing of Rotating Equipment (Pump, Motor and Compressor), P&ID’s and ISO’s of Piping.

·         Attend daily/weekly meetings as required.

·         Communicate effectively with EPC Contractor and CMT Group.

In process and Shutdown:                                                                         June 2013 – June 2014

Mechanical Field Engineer for the new project of HRSG and OTSG at Cenovus, Conklin-Christina lake facility.

Mechanical Field Engineer for the in-service OTSG project at Suncor – Fire bag facility.

Mechanical Field Engineer for the in-service Boiler project at Whitecourt Power LP, Whitecourtfacility.

Mechanical Field Engineer for the in-service Boiler project at Connacher Oil and Gas Limited, Conklin – Christina lake facility.

Mechanical Field Engineer for the in-service Boiler project at MEG ENERGY LTD – Christina lake facility.

Mechanical Field Engineer for the in-service Boiler project at Statoil, Conklin-Christina lake facility.

Mechanical Field Engineer for in-service OTSG project at Imperial Oil-Esso – Cold Lake facility.

Duties:

·         Involved in the Thermocouple addition project for four OTSGs

·         Involved in Tube replacement of addition project for OTSG.

·         Created, Implemented and followed ITPs

·         Weld Inspection

·         Performed visual inspection of ASME Section I, BEP and NBEP welds

·         Verify welder qualifications and Performed welder site orientations.

·         Plan, schedule and dispatch Non-Destructive Testing Personnel in accordance with project requirements

·         Updated history dockets on daily basis

·         Reviewed MTRs for code compliance

·         Create Hydro-Test Procedure and Conduct Hydro test of HRSG and OTSG.

·         Creating procedure for Pneumatic test for OTSG and HRSG

·         Conduct Pneumatic test of HRSG and OTSG.

·         Review Turnover Package.

·         Coordinate with Client and/or Authorized Inspector on all requested inspection activities

·         Co-ordinated all ABSA site inspections.

Mechanical Engineer in Trainee                                                                Jan 2013 – April 2013

Corrosion Monitoring – Coordinator

QA Upgrading – Suncor Energy-site

SGS Canada Inc.

Oil Sand & In Situ, Fort McMurray, Alberta

·         Creating accurate evaluations of Corrosion Monitor Locations in RBMI & Ultra Pipe software.

·         Calculating remaining life of piping based on API 570.

·         Generating reports for piping defects such as corrosion, erosion, bending, cracking, and sediment in Pipe. Creating Frame work in RBMI& Ultra Pipe with respect to Piping Specifications.

·         Worked with ASME B31.3, API 572 and API 570.

·         Knowledge of equipment specifications and data sheets, piping line classes, piping isometrics.

·         Checking Information in Live-link about pipe line and pressure vessel maintenance as well as location.

·         Editing P&ID drawing after inspection in field

·         Also walk down to plant and checking location as well as material of Pipe and Pipe components.

·         Conducts daily building walkthroughs of assigned portfolio and correct deficiencies.

·         Conducts detailed inspections to ensure that scheduled and periodic maintenance of equipment have been completed.

Mechanical Engineer (Production Engineer)                                            July 2010 – Dec2010

Puri Flair India Ltd

Baroda, Gujarat. India

·         Developed and revised existing equipment strategies for static and rotating mechanical equipment.

·         Provided support to Project Engineering during design and construction phases.

·         Reading & interpreting engineering drawings for the construction of vessels and piping.

·         Prepared designs of Heatless Dryers in Solid Works 2011 and converted in 2D drawing in Auto Cad 2010 as per ASME Sec VIII Div 1.

·         Witnessed LPI and MPI for pressure vessel parts

·         Coordinating experience with materials scheduling, work tasks and delegating work among team members which led to welding, grinding, drilling, boring assembling and hydro-testing of pressure vessels for heat exchanger parts.

EDUCATION:
Bachelors of Engineering – Mechanical Engineer                                                             June 2006 – June 2010

Gujarat University                                                                                                                  Gujarat, India

Diploma of Engineering – Mechanical Technician                                                            Jan 2011- Aug 2012

Sheridan Institute of Technology and Advanced Learning                                                    Brampton, ON

CWB Level 2 (ASME B31.3, ASME B31.1)                                                                       April 2014

Canadian Welding Bureau                                                                                                      Edmonton, AB

NACE CIP 2                                                                                                                          December 2015

NACE International                                                                                                                Edmonton, AB

IQAS (Mechanical Engineer – International educational credentials)                            December 2014

International Qualifications Assessment Service                                                                   Edmonton, AB

Maintenance Planning and Scheduling Training                                                              December 2016

Life Cycle Institute                                                                                                                 Edmonton, AB

SAFETY TRAINING AND CERTIFICATES:
Have current CSTS, OSSA, Air Purifying Respirator,H2S Alive, Confined space entry, Fall protection and ALTAIR 4X Multi-Gas Detector tickets.